Langendorf to present new version of the Flatliner at IAA trade fair
02.08.2018
Prefabricated elements for the most varied applications: quickly loaded, certified secure. The inloaders made by Langendorf save time and money (Figure: Langendorf/Robert Otto)
At this year’s IAA Nutzfahrzeuge trade fair in the German city of Nuremberg, in Hall 27, F 05, Langendorf, the Waltrop-based manufacturer with long tradition presents a vehicle from the SB series to the specialized trade professionals. The completely revised Flatliner impressively shows the range of possible missions.
The inloader of type SB-19 H 95/81 is used on all continents under the name Flatliner. An important advantage is the loading and unloading that needs no aids like a crane or lift truck, as the Flatliner must only take in a pallet (flat) that already carries the load on it.
Novelties
The most important innovations includes: The door retainers are now significantly more robust – an important safety aspect when loading and unloading on uneven terrain in strong winds.
All side storage compartments have been redesigned and are now even better protected against the ingress of spray water.
The operating elements have been redesigned from an ergonomic point of view and – as the inloader is in use worldwide – provided with universally understandable lasered operating pictograms.
Maintenance openings in the shaft inside now allow a more comfortable access to the slack adjusters. Thus, the care and maintenance of these important components is much easier.
The worktop on the two long girders – also called girder grate – now consists of GRP. Long-term tests have shown that GRP is less sensitive to soiling and thus significantly increases the safety of the driver.
Usability
Other visible changes include the rear portal. The hinged underrun protection is now made of aluminum and does not burden the driver with the same strength – when folding operation as strong as the previous steel design. In addition, the 270 ° rear door can now be retrofitted with minimal effort into a combi-door. This was not possible before.
The sum of the changes has many effects on the daily operation with minimal design changes of the vehicle.
The handling of the vehicle for the driver is more comfortable, the entrepreneur can always retrofit many options without much effort. That was previously only possible to a limited extent.
Intended for use behind two- or three-axle tractors, the empty weight could be reduced to approx. 9,500 kg. Thanks to the technically advanced single-wheel suspension, the loading shaft has a length of 9,500 mm and a width of 1,550 mm. This makes it possible to transport loads that are more than 9 m long and up to 3.7 m high in the loading shaft.
Loads of these dimensions are generally transported with low-loaders, although due to the load height or width, a special permit is often required. Most of the time, these transports are also linked to conditions. With the inloader, these requirements are frequently dropped, thereby providing maximum flexibility to the carrier.
Owing to the hydraulic lifting arm, no special technical requirements are needed on the tractor – any commercially available articulated truck can be used.
Loading in less than 10min
The hydraulics are self-sufficiently operated with the electric engine built in the trailer. The same engine also operates the fixing devices hydraulically. They can be adjusted horizontally and vertically so they can be flexibly adapted to the most varied loads and can be displaced in longitudinal direction on angled rails. In addition, a telescoping of the fixing arms is now possible. Therefore, the operation is fully possible from the ground and thus ensures the safety of the operating staff.
Up to five flat pallets can be taken in empty runs. To minimize tire wear and tear, the first and third axle can be lifted.
There is also the load restraint tested by TÜV Nord in May 2008 acc. to VDI 2700. The driver must only take in the pallet, secure it with the bracing device and can leave immediately. This means that the full loading process, including load securing, is completed in less than 10min – TÜV tested and certified. In addition, the vehicle is equipped with seven pairs of lashing rings on the longitudinal beams and every lashing point can be loaded here with 7.000 daN.
CONTACT
Langendorf GmbH
Bahnhofstraße 115
45731 Waltrop/Germany
+49 (0) 8000 92587-67
